SZLH series vertical ring die pellet machine absorbed the essence of pellet mill in oversea market, after our engineers improved; it had reached the international advanced level.

SZLH series of vertical ring die pellet machine is mainly applicable for difficult molding materials with low adhesion rate, for example rice husk, sunflower husk, peanut shell and fruit shell; branch, stem, rind and other wood waste; a variety of crop stalks; rubber, cement, ash and other chemical materials.

It can be used in feed mill, wood processing plants, fuel plants, fertilizer plants, chemical plants etc.

111

VERTICAL FEEDING

111

Vertical ring die fixed, roller rotating, with centrifugal force, making the materials evenly distributed around inside the die, also the centrifugal force will help improve the capacity.

111

The gearbox is processed by the German gear grinder niles, using a hard tooth surface helical gear to reduce speed, the tooth surface is widened by 20 mm, the module is increased, the degree of gearbox is large, the load capacity is improved, the operation

111

is more stable and the noise through the 5-level transmission is less than 75 db, its life is 3.5 times higher than conventional.

1111

It adopts hard tooth surface worm gear deceleration, widened tooth surface, increased modulus, large meshing degree and improved load capacity. Its life is 3-5 times that of the conventional reducer.

MOTOR POSITION

111

The motor and main shaft of pellet machine are parallel vertical installed , which can reduce energy consumption loss in the process of transmission, more output power, higher transformation of energy efficiency.

111

LUBRICATE SYSTEM

111

1)The lubricating oil of the gearbox adopts independent water cooling system, can lower oil temperature, and increase the service life of internal bearings.

111

2)The gear box is upgraded from a single oil pipe to a double oil pipe to ensure that the transmission parts of the gear box can be fully lubricated, thereby prolonging the service life of the machine. 10L/min

111

3)The spindle bearing uses the reducer's own thin oil lubrication, not only can reach the lubrication effect but also can lower the spindle bearing temperature.

DUST COLLECTOR SYSTEM

111

The pellet machine is equipped with an integrated dust removal system with shutters. cyclone is connected to a 9-cylinder dust bag, and the dust will be cleaned regularly from the bottom.

111

RING DIE AND ROLLER SKIN

111

The die hole is processed by ultra-high speed double gun drilling, and then through the hole grinding process to improve the smoothness of the discharge and the smoothness of the pellets;

1111

The material is made of high wear-resistant alloy steel, which undergoes a heat treatment process to increase the hardness of the mold itself and increase its service life. We also offer options of stainless steel ring die.

111

One ring die can be using 2 times by turn it over, which can cut down operating costs. The mold of the traditional pellet machine has 5 rows of holes. We have enlarged the granulating chamber and upgraded the mold to 6 rows of holes. The outer diameter of the mold is 690mm, the inner diameter is 550mm, and the thickness is 70mm. The roller skin is professionally carburized and has higher wear resistance.

ROLLER ASSEMBLY

111

The roller assembly adopts oil seal and filler double seal design to avoid grease leakage and dust ingress. The roller bearing adopts copper bracket self-aligning roller bearing design to improve the positioning effect of the roller. The roller bearing adopts eccentric type, and the squeezing force is stronger during operation, which is 1.5 times higher than the original pressure strength. The roller assembly is sealed by upper and lower glands. The thickness of the gland is high, which can ensure that it will not be deformed under high-temperature operation. And the gland is fixed by screws, so as to ensure that materials will not enter the roller assembly, thereby increasing the service life of the roller assembly.

111

RING DIE AND ROLLER SKIN

111

1)Bearing steel has high contact fatigue strength

111

2)High wear resistance of bearings

111

3)High hardness, so that the bearing can achieve higher contact fatigue strength and wear resistance

111

4)Bearings have good anti-rust performance

111

5)Bearings have good processing performance

SAWDUST PELLET MACHINE

EQUIPMENT PARAMETERS

111

MODEL	POWER	YIELD	WEIGHT	SIZE
SZLH470	45kw	0.7-1t/h	3.6t	2000×1550×1680mm
SZLH580	90kw	1-1.5t/h	5.5t	2400×1300×2100mm
SZLH660	132kw	1.5-2t/h	5.9t	2500×1300×1900mm
SZLH700	160kw	2-2.5t/h	7.6t	2514×1527×1995mm
SZLH860	220kw	3-3.5t/h	10t	2780×1950×2250mm

FLAT DIE EQUIPMENT PARAMETERS

111

MODEL	POWER	YIELD	WEIGHT	SIZE
SZLH350	37kw	300-500kg/h	1200kg	2150×800×1300mm
SZLH450	45kw	500-700kg/h	1400kg	2250×850×1350mm
SZLH550	55kw	700-900kg/h	1600kg	2300×900×1400mm

APPLICABLE MATERIALS

Biomass pellets are made from biomass materials such as wood, grass, rice husks, alfalfa, etc., which are processed into biomass pellets by a pellet mill.

Grass Pellet

Waste Wood to Make Biomass Pellets

Rice Husk Pellet Processing

Cashew Husk

Peanut shells turn waste into treasure

Straw for Pellets Fuel Production

MANUFACTURER ADVANTAGE

Kingoro takes the largest market share in China.

Thousands of biomass pellet production lines have been installed and running successfully worldwide.

Customers can visit and see our production running conveniently.

Our group company has been founded in the Year 1995. We have 27 years' experience in making the machinery.

We have built the first advanced manufacturing institute in our city with the famous university

Our brand "Kingoro" is famous in China.

We are the leader in the Biomass

Pellet Mill Industry, we have 49 Patents

and 3 Industry-standard drafters.

We know-how about the Biomass Pellet,

Biomass Pellet Mills, and Biomass

Pellet Production Lines.

There have a separate raw material trial test area for our customers, we have a trial test for many raw materials including but not limited to wood log, wood chips, wood sawdust, rice husk, straw, sugar cane, palm shell, sunflower husk, building template, wood tray, furniture scraps.

After thousands of trial tests with different machines and different dies with different compression ratios, we can give our customer most suitable machine with the proper rind dies mold and most adequate compression ratio.

The pellet mills can be running 24 hours, our pellet mills first adopt advanced four-gear shaft transmission.

The reducer and the main shaft are designed to share the same flowing oil lubricating system.

The angle contact bearings of the main shaft are fully lubricated with no oil pollution.

The observation window is installed on the reducer.

Cooperate with the famous university, we have designed an advanced intelligent control system,which can control the whole system with their logical sequence through downing the App on mobile and the PLC which has been installed on the system.

The advanced new grease pump has been installed as an integration of the pellet mills. Compare with the old grease pump of our competitors, it saves over 50% of the grease cost.

The pellet mills adopt the helical harden gear transmission system, the output shaft connects with the main shaft by the spline. The efficiency of the pellet mills is enhanced by 20%.

Online Message

300.cn SEO